_GOTOBOTTOM
Armor/AFV
For discussions on tanks, artillery, jeeps, etc.
White 666 hard cab winch cable Q.
alewar
Visit this Community
Canelones, Uruguay
Joined: December 27, 2006
KitMaker: 773 posts
Armorama: 765 posts
Posted: Thursday, November 07, 2019 - 07:23 AM UTC
Hi all

Does anyone have a clear picture of where the winch cable extends when it is being operated? I have read the TM but it just says that the cable run on sheavers on the underside of the cargo body. And is pulled out fron the roller under the tool box at the rear of the vehicle. But the toolbox is not on the side?.
I want to represent the truck pulling some other vehicle. Some help?.
TIA
Alvaro
Frenchy
Visit this Community
Rhone, France
Joined: December 02, 2002
KitMaker: 12,719 posts
Armorama: 12,507 posts
Posted: Thursday, November 07, 2019 - 08:24 AM UTC
Here's a rear view showing the end of the cable :


The tool box you're talking about is located between the tail lights

H.P.
OldWarloke
Visit this Community
United States
Joined: October 14, 2012
KitMaker: 2,663 posts
Armorama: 2,649 posts
Posted: Thursday, November 07, 2019 - 08:38 AM UTC
Most likely the winch wouldn't be strong enough to pull most vehicles.
It was used to pull trailers and artillery pieces closer to the back end to hook them up.
Donald
Frenchy
Visit this Community
Rhone, France
Joined: December 02, 2002
KitMaker: 12,719 posts
Armorama: 12,507 posts
Posted: Thursday, November 07, 2019 - 08:46 AM UTC
The mid-mounted winch has a 25,000 lb (11,000 kg) capacity.

H.P.
alewar
Visit this Community
Canelones, Uruguay
Joined: December 27, 2006
KitMaker: 773 posts
Armorama: 765 posts
Posted: Friday, November 08, 2019 - 01:23 AM UTC
Thanks Henri-Pierre and Donald.

165thspc
#521
Visit this Community
Kentucky, United States
Joined: April 13, 2011
KitMaker: 9,465 posts
Armorama: 8,695 posts
Posted: Friday, November 08, 2019 - 04:06 AM UTC
On a subject that is closely related - well it's relatively close anyway (physically) - to what we are looking at here in this thread -
that tool drawer:

This is a detail that while present on every CCKW, White, Dia. T and Mack model truck ever offered it is never actually modeled. - that tool drawer.

Here is "the rest of the story" as modeled on my Diamond T Wrecker:




And here again, as seen below, another shot of that tool drawer on a derelict CCKW. Unfortunately I have never seen an image of this drawer in the open position - Frenchy ??????

Frenchy
Visit this Community
Rhone, France
Joined: December 02, 2002
KitMaker: 12,719 posts
Armorama: 12,507 posts
Posted: Friday, November 08, 2019 - 04:36 AM UTC
Same here Mike...Maybe it's because it has never been opened by anyone

H.P.
165thspc
#521
Visit this Community
Kentucky, United States
Joined: April 13, 2011
KitMaker: 9,465 posts
Armorama: 8,695 posts
Posted: Friday, November 08, 2019 - 05:41 AM UTC
I have always suspected that between rust and the slight warpage of the load box body these tool drawers quickly became unusable.

It just seems like there would be in a TM somewhere, a photo of one of these in the open position.

What I do know is that while the drawer front is always modeled the under body toolbox itself almost never is.
Namabiiru
Staff MemberAssociate Editor
MODEL SHIPWRIGHTS
#399
Visit this Community
Rhode Island, United States
Joined: March 05, 2014
KitMaker: 2,888 posts
Armorama: 1,920 posts
Posted: Saturday, November 09, 2019 - 01:38 AM UTC
Would there have been a drawer in there? Given the shape (deep and flat), it seems like getting at anything you put in there would be a real pain, especially after stopping the vehicle and everything slides to the front.

165thspc
#521
Visit this Community
Kentucky, United States
Joined: April 13, 2011
KitMaker: 9,465 posts
Armorama: 8,695 posts
Posted: Saturday, November 09, 2019 - 01:52 AM UTC
The way the locking hasp drops downward it is either a drawer or a horizontal hinged door that opens upward. (Hinged across the top.)

Have never really been sure, which is why I was asking if anyone had a TM photo of it open.
165thspc
#521
Visit this Community
Kentucky, United States
Joined: April 13, 2011
KitMaker: 9,465 posts
Armorama: 8,695 posts
Posted: Saturday, November 09, 2019 - 02:02 AM UTC
According to the G503 website the TM indicates that the starting crank is stored in this compartment. Which for the Deuce with winch can be quite long.

Also it appears to be a door, hinged along the top of the opening rather than a drawer.
 _GOTOTOP