login   |    register
 

How to make a metal plate

How to make steel plates using cardboard
After making some steel loads for my 1/24 haulage, I received many request for a 'How-to' article on how I made them. So, here goes. I tend to look for easier ways to achieve the end results with fewer procedures. Sometimes itís hard to not do tutorials with long steps but sometimes it is necessary to give an absolute accurate procedure that will make it easier for others to follow and understand. Now my method is certainly not the only way, so if you know of a much easier method by all means, use it. After-all, itís the end result that counts. The materials used are ones I had on hand. They are not a must to have for doing these steps. An equivalent will do just fine. So letís get on with it.

List of things to help achieve the end results:

* Poster board
* Sharp Blade
* Metal edge ruler
* Black primer paint
* Brown paint (I used Tamiya earth spray paint)
* White felt pen (optional)
* Mig's light and standard rust pigments (or any other brand)
* White Felt marker (this is optional if you want markings on the steel)
* Small old brush (preferably one with short round bristles)
* Medium size round brush (It does not have to be round. I just think it makes the job easier when applying the pigment to conform to the desired patterns)
* Mig's odorless enamel thinner (I guess any brand would do and it doesn't have to be odorless either. Itís just easier on the nose)
* Matt varnish (I used Vallejo but I guess any brand will do. Test first to see so it won't ruin the effect of the end result)
* Steel metallic color (my favorite is Leadbelcher from Citadel. Always use it in my modeling. But once again, if you prefer another brand, be my guest)
* Wide/medium size flat brush (this will be used for dry-brushing)

Step one:
1. Cut a piece of the required cardboard you are going to use for this procedure. (One important note when cutting cardboard. Always, Always, use a sharp hobby knife and a straight-edge ruler to cut the arks you need, to size. This way you will get nice clean edges. If not the edges will look weird and out of place. Make sure the edges don't buckle up as well. It will definitely, not look right as steel plates don't buckle up in that fashion)

move
Metal edge Ruler with a sharp hand blade (click to expand)

move
The poster board in this photo is the size I used (click to expand)

move
Your cuts should be almost clean and should not have any buckles in them, like in this photo (click to expand)

2. Spray both sides of the cardboard with your black primer. (And from here on, we'll just concentrate working on one side, as the rest of the procedure can be repeated on the other side when you are completely done with the first side).

move
The piece of poster board painted with chaos black (click to expand)

3. Spray brown paint in patches over the cardboard. Do not cover the entire cardboard with the brown paint (I guess you could but you can do that on the opposite side when you have completed the side you are already working on. Just let some of the black show through. The aim is that you are trying to make variations or in the way the steel will look in the end. More of a 2D effect. Let dry thoroughly before proceeding to the next procedure).

move
Tamiya Red Brown. You can use any other brown you prefer (click to expand)

move
You can see some of the black showing through (click to expand)

4. (This procedure is optional, but if you decide to do it, it will add some cool optional effect to the overall steel plates.) Take your white felt marker and write some digits onto the plates. I have seen certain markings on a few. Some are digitally written or hand written. Unfortunately, I have not done further research to find out what they mean. I will leave that up to you to decide. Reference pics always help.

move
White felt pen (click to expand)

READ COUNT: 4185  |  Printer friendly page PRINT  |  Discuss This DISCUSS THIS

About Charles King (ti)
FROM: DALARNAS, SWEDEN

Charles King hails from Sweden. He has been interested in modeling since he was 12; though there was other interest that took priority at the time, he would eventually fall into the modeling soon enough. Not until recent,in 2002 that his interest was rekindled. While browsing the Internet, he ca...